- filter monitor for in-situ dust measurement
- compact device
- display showing the measured value in mg/m³ or in line diagram
-
-
- continuous, tribo-electric in-situ filter monitoring device with EC-Type Examination Certificate (IBExU19ATEXB008 X)
- approved for Ex II 3D Ex ic tc IIIC T80 °C Dc
- suitable for installations in hazardous areas of zone 22
- no separate power supply necessary (2-wire transmitter)
- two probe lengths available (300 and 500 mm)
-
- filter monitor for in-situ dust measurement
- compact device
- suitable for the construction of filter monitoring systems
-
- filter monitor for in-situ dust measurement
- compact device with display
- suitable for the construction of filter monitoring systems
-
- filter monitor for in-situ dust measurement
- with separate operating unit
- display showing the measured value in mg/m³ or line diagram
-
- intelligent system for isokinetic dust and fine particles measurements in exhaust air ducts and stacks
- acquisition of all necessary gas boundary parameters (humidity of the sample gas, velocity in exhaust gas channel, temperature, pressure)
- pivotable graphic display for more convenient operations
-
- patented world innovation: Sampling and weighting in one system on site!
- intelligent system for isokinetic dust and fine particles measurements in exhaust air ducts and stacks
- acquisition of all necessary gas boundary parameters (humidity of the sample gas, velocity in exhaust gas channel, temperature, pressure)
- pivotable graphic display for more convenient operations
-
- mobile filter diagnosis unit for triboelectric in-situ monitoring of dust emissions
- measuring probe with variable length to adapt to the local conditions
- immediate clean gas dust content monitoring after the dust collectors
- offline power supply by power bank
- integrated recorder
-
- real-time measurement of PM2,5
- Monitoring of fine dust concentrations in ambient air and/or at workplaces
- optical sensor including fitting with clip system, therefore easily exchangeable
- active and automatic zero point setting
- active air suction
- Integrated pre-separator for particles > 2,5 µm
- noiseless operation
- network-compatible
-
- simultaneous real-time measurement of PM10 & PM2.5
- based on optical sensor, active suction & patented electrostatic precipitator for zero point setting
- flexible use - indoors & outdoors -
- portable case with offline power supply by power bank
- including data logger for storage of measuring values
-
- optical sensor for continuous, simultaneous measurement and control of fine dust contents PM10/TSP and PM2,5
- patented zero point control by electrostatic precipitator
- smart, robust, network-capable
- simple unit design
- installation without any special tools
-
Optical sensor for continuous measurement and monitoring of fine dust contents indoor and outdoor.
- optical sensor for continuous measurement and monitoring of fine dust concentrations (PM10, PM2.5)
- smart, robust, network-capable
- simple unit design
- installation without any special tools
-
- extractive optic dust concentration measurement
- measurement in wet, sticky exhaust gas conditions
- optical dust sensor
- suitability tested according to EN 15267-3 (QAL1)
- approved for installations according to IED
-
Optimization of combustion efficiency and compliance with environmental standards Ideal for combustion control in boilers, incinerators and furnaces. Lowering CO₂, SOx, and NOx emissions while saving energy This oxygen analyser is used to continuously measure oxygen concentration in combustion exhaust gas of industrial boilers or furnaces, and is ideally suited for combustion management and control, such as garbage incinerators and smallest to largest sized boilers, as combustion controllers, achieving a significant energy-saving effect. -
Reliable process control for furnaces, metal industry, semiconductor and gas separation. The analyser continuously measures the concentration of gases such as H2, He, and Ar with high stability. It is also available in a version for hazardous areas (for countries outside the European Union): ZAFE certified Ex NEPSI. -
Ex-proof in situ zirconia oxygen analyzer for combustion controlThe oxygen measurement enables the control of burner fuel/air ratios to ensure combustion efficiency and process safety. Fuji Electric O2 Analyser is adapted to be installed in hazardous areas and to withstand critical environments as:- Refinery process heaters
- Petrochemical reactor furnaces
- Industrial large scale boilers