The sensors are installed directly in pipes or in tanks.
The sensors are used, for example, in oils, crude oils, paints, lacquers, ethanol, solvents as well as in bulk materials under explosive conditions.
-
The MMS system basically comprises a multiplexer-valve unit and the highly accurate and selective mercury detector VM-3000 Vapor Monitor. A bypass pump maintains a steady flow of sample through the sample filters, sample lines and multiplexer valves. Flow meters with optical alarm sensors guarantee that flow rates are stable. All components are installed inside a protective cabinet. -
The ACC cooler offers precision, safety and long-term stability for extractive analytics. The very low gas dissolution rate is attained owing to the new cooler technology (Patents applied). Both the permanent separation of the condensate from the gas phase, as well as the shorter contact time of the gas in the system, plays important roles in reducing gas dissolution rates. The new cooler incorporates an advanced structural design with housing suitable for both wall-mounting (standard) and 19“-racks by using optional brackets. The coolers can be integrated into the analysis cabinet without empty space requirements at the side for a cooling air outlet. The design enables 1 or 2 heat exchangers to be incorporated either at the factory or at a later time, without any problem. The exchangers can be connected in series or parallel following customer requirements. An electronic system monitors the dew point and controls the integrated fan. A temperature alarm output is wired to the terminal block incorporated of the cooler housing for a safe connection without disassembling the cooler.Available for 230 VAC and 115 VAC power supply.
-
In-line Fiber Optic Measurement cells
Kemtrak industrial process measurement cells are manufactured from the highest quality materials and are designed to the most demanding specifications to ensure long life and the highest reliability. Industrial grade fiber optics transmit cold light to the measurement cell and back. The measurement cell contains no electronics, moving parts or sources of heat that would result in condensation on the optical surfaces and they are well suited for hazardous area operation. -
The Protea 2000 emissions monitoring system is approved forthe analysis of exhaust gases from the engines and boilers of ships and offshore rigs. Robust and with proven reliability, up to six gases can be measured including SO2,CO2 The Protea 2000 emissions monitoring system comprises up to 8 exhaust mounted analysers, each with automatic verification facilities. Emissions data from the entire system is securely managed and displayed at a dedicated Classification Society approved panel PC, with outputs to networks, control systems, and reporting facilities. -
Small, fine, excellent: The Liebherr P30-S sensor in conjunction with the Liebherr FMS moisture measuring installation has become indispensable for many industrial processes. The “Little One” expanded our product portfolio in 2008. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the sensor has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age. -
The Liebherr P78-SC sensor in conjunction with the Liebherr Litronic-FMS/CCS type coating thickness and basis weight determination system has become indispensable for many industrial processes. The areas of use include the coating of paper, box, film, non-woven and textile webs. The sensor installations take place, for example, before and after the squeegee for the exact determination of the coating or the humidity The Litronic-FMS III evaluation and transfer unit, which is a mandatory part of the system, is used to record, process and prepare the values measured by the sensors. The integrated software is used for convenient parametrisation and calibration. Thanks to the various interfaces, signal transmission to the higher-level control is feasible. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the sensor has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age. -
The Liebherr in situ water content determination Litronic-FMS III-RMH12 is used to detect the water content (concentration determination) even in very low ppm ranges in emulsions such as diesel fuel, transmission, hydraulic, engine, roller bearing, transformer and turbine oil as well as in battery systems. -
The CAN bus is used in on- and off-road applications, vehicles in the construction and agricultural sectors as well as in engines. The CAN bus is integrated in the sensor. The sensor meets critical EMC and environmental requirements. The signals are integrated and processed directly in the customer's control. The CAN bus signals communicate directly with the control apparatus. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the sensor system from Bad Schussenried is characterised by its reproducibility. Each CAN sensor is individually calibrated and final tested. -
Small, fine, excellent: The Liebherr P78 sensor in conjunction with the Liebherr FMS moisture measuring installation has become indispensable for many industrial processes. The moisture measuring installation was invented in 1985 at the Bad Schussenried factory. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the sensor has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age. -
A self-sufficient moisture measuring installation with high connectivity and many interesting possibilities. With ProfiNet technology on board, extensive signal processing and WEB-based access, we are ready for Industry 4.0. Without Ethernet support, these tasks cannot be accomplished. At the beginning of each measured section, the calibration per product must be carried out by means of reference procedures. The Litronic-FMS IV software enables convenient and rapid parametrisation. The evaluation unit receives the raw values measured by the Liebherr sensors and immediately converts them into the measured value, such as percentage humidity. Up to 16 sensors can be managed via the WEB with one device. A curve manager and material and sample management helps the user to create the product-specific calibration. Once the system has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. A sensor exchange or a transfer to another measured section is also possible without recalibration. -
A self-sufficient system with almost unlimited possibilities. The Litronic FMS II type moisture measuring installation has been used for decades in a wide range of industries to measure the moisture content of various materials in real time.At the beginning of each measurement section, the calibration per product must be carried out by means of reference procedures. The Litronic-FMS II software enables convenient and fast parameterisation. The evaluation unit receives the raw values measured by the Liebherr sensors and immediately converts them into percentage humidity. Thanks to the various interfaces, transfer to a higher-level control is possible. Measurement by the Liebherr sensor system is based on the physical principle of capacitance determination in the high-frequency stray field. In addition to their high precision and robustness, the measuring devices from Bad Schussenried are characterised by their reproducibility. Once the system has been calibrated, further measuring points can be set up or devices renewed on this basis at any time without great effort. The plant thus always remains reliable, regardless of its previous term and age. -
The ALS liquid-stop protects analyzers against an inrush of liquids from the gas conditioning unit into the analyzer.
This avoids major damages of the analyser.
The best position of the liquid is behind the gas conditioning unit, and before the flow meter going to the analyser.
-
The self-sufficient measuring device for precise water content/moisture determination in the running process guarantees the highest quality and safety in EX-protected production environments, the further processing and refinement of very many emulsions and bulk materials. The PC software enables fast and accurate calibration of the measured sections. -
NEO Monitors’ LaserInspect™ CIMO4 gives the operator the opportunity to remotely operate up to 4 LaserGas™ analyzers from the same display*. The operator have full status overview in an instance of all instruments and is able to perform maintenance tasks directly from the panel. This HMI is designed for the NEO Monitors LaserGas™ family and can easily be integrated into a cabinet. * Separate Ethernet switch is required to operate multiple analyzers -
LaserGas™ III Ultra
It uses the innovative baseline-insensitive TDLAS technique specifically designed for combustion analysis. The Ultra simultaneously meets the requirements of combustion control and safety. That is, high measurement accuracy and high dynamic range with simultaneous real-time measurement capability. Applications with very long path lengths and high gas concentrations are no problem for the Ultra. Thanks to the baseline insensitivity and the use of the proprietary IROSS signal processing, high measurement accuracy is achieved even with complex gas mixtures. LaserGas™ III Ultra CO in combination with LaserGas™ III O2 are a perfect combination for proper combustion control and safety. -
In tegenstelling tot de vorige generaties LaserGas™-producten, meet de LaserGas™ Q-familie in het mid-infraroodspectrum, wat betere detectielimieten mogelijk maakt. Evenals detectie van gassen die niet mogelijk zijn met de meer gebruikelijke nabij-infraroodspectroscopie. De sensor heeft lage onderhoudskosten en vereist geen regelmatig onderhoud. De afwezigheid van extractieve conditioneringssystemen verbetert de beschikbaarheid van de metingen verder en elimineert fouten met betrekking tot monsterbehandeling. De monitor is direct op flenzen gemonteerd, die zijn voorzien van spoelgasaansluitingen en een kantelmechanisme voor eenvoudige uitlijning. Een continue spoelstroom voorkomt dat stof en andere verontreinigingen zich op de optische vensters nestelen. Zodra stroom- en datalijnen zijn aangesloten, worden metingen in realtime uitgevoerd. Download datasheet